starflix.blogg.se - Phineas and ferb owca files full episode

PHINEAS AND FERB OWCA FILES FULL EPISODE SERIAL
PHINEAS AND FERB OWCA FILES FULL EPISODE MANUAL
PHINEAS AND FERB OWCA FILES FULL EPISODE SOFTWARE
PHINEAS AND FERB OWCA FILES FULL EPISODE PC
PHINEAS AND FERB OWCA FILES FULL EPISODE DOWNLOAD

You shall create holes to let emergent parts to exit from its surface: the socket, the two leds (or a single bi-colour led), the USB socket on a short side. Just the socket and the two leds shall emerge. Use countersunk screws of countersunk holes to avoid the screws being too hight respect to upper surface of second PCB. Once the two circuits are ready, connect them using the strip lines, and block assembly using the columns. During soldering jump several pins each time, following a spiral line, adopting a sequence that allow to warm-down a pin while you are soldering the next one. It is better to do 1.2 mm holes to facilitate the insertion of the ZIF socket in the PCB. Pay attention to avoid any force that can lead to damage or deformation. The ZIF is a quite delicate component befor final soldering.

PHINEAS AND FERB OWCA FILES FULL EPISODE MANUAL

Use low profiles parts to fix the columns, otherwise some manual metals removal can be needed to reduce the occupation on the copper side. Mount 4 ten millimeters height columns to allow the final assembly of the second board. Schematicīuild first the main module using low profile components being under 10 mm of height from the PCB surface, since a second board will be mounted over that one.

PHINEAS AND FERB OWCA FILES FULL EPISODE SOFTWARE

Take into account that, on the original site, a newer version of both Firmware and Software is available. I tested the program up to Win-8 without problems.

PHINEAS AND FERB OWCA FILES FULL EPISODE PC

At the bottom of this page, I supply a copy of the program to load on the PIC18F2550 used to manage the programming functions, as well as a copy of the PC side program. Hereafter, I shown my Compact version, with a schematic, PCB layout and instruction for assemby and inserting it in a very common little plastic box. The details are available on the original project mentionned above. Anyway, if your goal is to program PIC devices, you are on the good site.Ī small box, a USB connector, a ZIF socket, two leds. I will thank everybody proposing a larger range implementation, suitable to program Atmel and other devices. This version sacrifices many non-PIC microcontroller models.

So, I propose here a small layout version of that circuit, adopting a single smart on-board ZIF socket. Moreover, the proposed layout did not meet my personal “compact look” ideas. What concerned me was the need to mount, on the mainboard, a specific socket board depending on the model of PIC being programmed. Looking on the web for ready-to-use projects, I found a good one called Open Programmer, coming with several schematics, PCBs and Open Source code. The figure 1, 2,and 3 below shows the header pinouts of different interfaces.This page is dedicated to everybody needs to program a PIC (Microchip) device via USB port.

Target board connection via JTAG, AS, PS interfaces.

Computer connection via USB 2.0 interface.

Enhanced Configuration Devices including: EPC1, EPC4 etc.

PHINEAS AND FERB OWCA FILES FULL EPISODE SERIAL

Active Serial Configuration Devices including: EPCS1, EPCS4, EPCS16 etc.FPGA: Stratix, Stratix II, Cyclone, Cyclone II, CycloneIII, ACEX 1K, APEX 20K and FLEX 10K etc.Tested devices are listed below, including but not limited to: NIOS II EDS integrated development environment.NIOS II IDE integrated development environment.Quartus II integrated development environment.Supports Nios II of embedded processor communication and debugging.Supports SignalTap II embedded logic analyzer.High-speed, stable, and internal FT245R+CPLD designed.

PHINEAS AND FERB OWCA FILES FULL EPISODE DOWNLOAD

Supports AS, PS, JTAG three download modes.

Supports most of the ALTERA FPGA/CPLD devices, Active Serial Configuration devices, and Enhanced Configuration Devices.

Download speed 1-3 times faster than other schemes, such as 68013 or C8051F.

High speed FT245+CPLD+244 solution, similar download speed as the original ALTERA USB Blaster, with the same operation.

It surpports most of the ALTERA FPGA/CPLD devices, Active Serial Configuration devices, Enhanced Configuration devices, and supports AS, PS, JTAG three download modes. You can use the USB Blaster cable to iteratively download configuration data to a system during prototyping or to program data into the system during production. The cable sends configuration data from the PC to a standard 10-pin header connected to the FPGA. The USB Blaster Download Cable interfaces a USB port on a host computer to an Altera® FPGA mounted on a printed circuit board. USB Blaster Download Cable is designed for ALTERA FPGA, CPLD, Active Serial Configuration Devices and Enhanced Configuration Devices, USB 2.0 connection to the PC and JTAG, AS, PS to the target device.